Hatchback

Mounts for clamping on a boot or hatchback.

The boot mounts are designed to fit on a "traditional" flat boot. The surface must be close to horizontal, otherwise the antenna will not stand up straight.

The hatchback mount is similar to the boot mount, but the angle of the mount can be adjusted to suit the slope of the hatchback.  Can be fitted on the top of the side of the hatch.

3/8 Boot Mount (with coax)

B19a
Add to cart

A small 3/8 thread boot mount, to clamp on a standard size car boot lip.

Will only fit on a flat horizontal boot (or similar lip), there is no adjustment for angle.

Supplied complete with a fitted coax lead and plug  (approx 4m).

PNI SO239 Boot Mount

MT941
SOLD OUT

A stainless steel boot mount for use with any SO239 fitting antenna.

Designed to fit on a flat horizontal surface, the angle of the mount is not adjustable.

Supplied with 5m of coax and a PL259 plug fitted.

SO239 Boot Mount (with coax)

15-069
Add to cart

A small boot mount with SO239 fitting, to clamp on a standard size car boot lip.

Will only fit on a flat horizontal boot (or similar lip), there is no adjustment for angle.

Supplied complete with a fitted coax lead and plug  (approx 4m).

Hatchback Mount with Coax

B82
Add to cart
Last Few

A 3/8 thread mount designed for clamping on a hatchback.

The mount can be swivelled in 2 directions - this allows the mount to be used on either the top or the side of the hatchback, and for it to be adjusted to suit the slope of the hatch.

Supplied complete with a fitted coax lead and plug (approx 4m).

President LS-11CPL Boot Mount

LS11
Add to cart

A boot/trunk mount with SO239 fitting.

Supplied complete with 3.6m coax and fitted PL259.

Will fit any SO239 fitting antenna - such as varios Sirio, President and Maas models.

Sirio Trunk-Top 2

B74a
Discontinued

A good quality boot mount, designed to fit on a standard horizontal car boot.

The mount has an SO239 fitting (as in picture) but also comes with a 3/8 adapter which screws on top of the mount to allow you to use a standard 3/8 thread antenna on it.

Supplied complete with a fitted coax lead and plug (approx 4m).

Stainless Steel Hatchback Mount

15-009
SOLD OUT

An adjustable stainless steel hatchback mount.

  • Adjustable in 2 directions
  • Stainless Steel
  • Suitable for SO239 cable assemblys

Slim Adjustable Hatchback Mount

15-0111
Add to cart

Black adjustable hatchback mount.

Easily adjusted either for angle or to fold the antenna down.

  • Black powder coated 
  • Size: 50 x 50mm  
  • Fully adjustable horizontal and vertical
Add to cart

A stainless steel adjustable hatchback mount suitable for use on most hatchbacks and boots.

The mount has a 16mm hole in it and requires a suitable mount and coax to complete it (eg ECH kit). It is held to the vehicle with 4 grub screws.

A large locking control allows you to fold the antenna down for entering your garage etc.

Add to cart

A black adjustable hatchback mount suitable for use on most hatchbacks and boots.

The mount has a 16mm hole in it and requires a suitable mount and coax to complete it (eg ECH kit). It is held to the vehicle with 4 grub screws.

There is a swivel connection between the base plate and the mount, so you can swivel the mount about both axies.

We have sometimes found that they have put too much paint on these when they made them, and you may need to scrape a little off to ensure a good earth connection.

Add to cart

A black adjustable hatchback mount suitable for use on most hatchbacks and boots.

The mount has a 16mm hole in it and requires a suitable mount and coax to complete it (eg ECH kit). It is held to the vehicle with 4 grub screws.

We have sometimes found that they have put too much paint on these when they made them, and you may need to scrape a little off to ensure a good earth connection.