A  Wall Bracket supplied complete with two 1.75" U-Bolts.

Available in 6", 9" and 12" arm lengths.  Please note this is measured to the end of the bracket, so the pole will be about 2" closer to the wall than this.

The height of the brackets are 6" for the 6" & 9" arms, and 12" for the 12" arms.

We also now have a 9" x 9" bracket available.

Heavy duty 18" x 12"  galvanised single wall bracket supplied complete with U-Bolts.

The arms measure 18" to the end (giving about 15" clearance) and the height is 12".

A pair of Wall Brackets supplied either on their own or with two U-Bolts (choose from 1.75" or 2.5").

Available in 12", 18", or 24".  Please note this is measured to the end of the bracket, so the pole will be about 3" closer to the wall than this.

A pair of Wall Brackets supplied either on their own or with two U-Bolts (choose from 1.75" or 2.5").

These are heavy duty galvanised brackets, rather than the standard painted ones.

Available in 12", 18", or 24".  Please note this is measured to the end of the bracket, so the pole will be about 3" closer to the wall than this.

A lightweight pole and bracket, ideal for mounting small base antennas to a wall or facia or in the loft.

Pole stands approx 12" from wall and is approx 22" high. Diameter 1".

Obviously the pole could be turned around so that they stand out further from the wall (with the shorter length vertical).

These are only suitable for small antennas (probably up to 9ft) and will not be strong enough for larger base antennas.

A compact wall bracket ideal for mounting a small base antenna direct to a wall (eg Sirio Boomerang or Sigma Excalibur).

Provides a short section of 1.5" diameter pole to clamp your antenna to.

A heavy duty welded lashing kit, consisting of a 6" bracket, lashing wire and u-bolts.

• 6" welded bracket
• Lashing wire
• 2 x 1.5" U-bolts
• 3 x corner plates
• 2 x J-bolts

A heavy duty "cradle" style chimney lashing kit.

• 13.5" welded bracket
• Lashing wire
• 2 x 2" U-bolts
• 3 x corner plates
• 2 x J-bolts

A repair kit for chimney lashing kits, consisting of:

• Lashing wire
• 3 x chimney corner brackets
• 2 x U-bolts
• 2 x J-bolts

A repair kit for double chimney lashing kits, consisting of:

• 2 x Lashing wire
• 6 x chimney corner brackets
• 2 x U-bolts
• 4 x J-bolts

Note: picture shows the single lashing kit

Replacement U Bolts for use on brackets and antennas.

The standard 1.5" and 2" are the ones supplied with our brackets. 

The 1.5" version will fit poles up to 1.5" and actually measure 1.75" centre to centre, the 2" ones fit up to 2" poles and measure 2.5" centre to centre. 

The "antenna" u-bolts are the slimmer type 1.5" ones which come with the standard British made base antennas (and many other antennas).

A clamp for joining 2 poles up to 2" in diameter.  Will clamp down to any smaller size.

You will usually require 2 of these, spaced a reasonable distance apart.

A clamp for joining 2 poles up to 2" in diameter.  Will clamp down to any smaller size.

Because of the design of this bracket you can use it to join 2 poles either in parallel or at right angles to each other (ie to add a cross-bar etc). 

When used as a right angle joiner, the maximum diameter of the second pole is 1.5".

A genuine bracket from Sirio designed to allow you to mount the Sirio 827 onto any size pole from 1.25" to 2" diameter.

Normally these antenna sit "on top" of the mounting pole, which must be 35-40mm to fit correctly, this adaptor consists of a short length of the correct size poles connected to a a pair of U-bolts that will fit poles up to 2" diameter.

Can also be used for mounting any other antennas on a 2" pole when there brackets usually only accept smaller poles.

Similar to "rawl bolts" but much cheaper.

Requires a 10mm masonry drill.

A large plastic wall plug and seperate bolt.

Now also available in box of 100 at a big discount!

A 4ft copper plated earth rod complete with clamp for attaching an earth wire.

A good earth connection can not only help reduce interference but can also improve performance of your station.

A guy rope clamp to fit poles from 1.25" to 2" diameter.

Hooks for 3 guy wires.

A guy rope clamp to fit poles from 1.75" to 3" diameter.

Hooks for 4 guy wires.

A metal joining sleeve to join 2 poles together.

Available for 1.25", 1.5" and 2" poles.