A range of replacement 12V power leads to suit many types of CB & Amateur radios.
All come supplied with in-line fuse holder and fitted fuse.
Popular replacement power lead to suit most Cybernet boarded radios.
Examples include: Harrier, Rotel, York, Harvard, Radiomobile etc
Very slightly larger than the 2 pin round, this was used in just a few radios such as the Communicator.
The 2 pin round lead above will actually fit these radios, so if in doubt get the rounded one.
Replacement power lead to suit most Midland radios plus a few other makes.
Examples include: Midland 77-104, Midland 78, Midland 48, etc
3A or 7A versions
A popular 3 pin power lead, with 2 of the pins closer together to prevent you plugging it in wrong way around.
Available as standard (for standard FM CB's) or heavy duty (7A) for multimode radios.
Examples include: Uniden, Audioline, Cobra, etc
An extra heavy duty 3 pin power lead (15A) with a cig lighter plug fitted.
Made by K40, and designed for high power radios, this power lead is made with a 1.8m long 15A cable and is fitted with a fused cig lighter plug.
An unusual power lead because it has 3 wires rather than 2. There are normal live and earth wires, plus a memory wire (permanent live).
The only radios I know that use this are the Maxon MX1000 and MX2000, but there are probably others.
Replacement original power lead for the Maxcom 7E portable CB.
Comes complete with a fitted fused cig plug.
Note: these are old stock and may show some signs of corrosion where they have been stored in a damp place, but will all work OK.
Any 10 x Power Leads
A mix of any 10 of the above standard power leads (any priced at £2.50 each).
Just note which leads and the quantities in the box provided on the right.
Sold Out - discontinued
A small power lead with 1 round and 1 square pin.
Fits: some Amstrads, Mustang, Pama. Does not fit early Amstrad radios that had a power lead with a clip at each end rather than 1 in the middle.
On some radios we find that the clip is too "thick" and you may have to shave a little off the side of the clip to make it clip in.
These power leads/sockets are notorious for being a loose fit, especially once the radio gets a few years old.
A popular 3 pin power lead for early Midland & Maxcom radios, with clip on side.
Examples include: older Midlands, Maxcom, Commtron, etc
Unfortunately this lead has been discontinued and the only stock we have been able to find is very expensive!!
Original replacement power lead for tti radios.
Fits TCB-550, TCB-660, TCB-770, TCB-771, TCB-880, TCB-881 and TCB-1100.
Replacement power lead for CRT SS9900.
"T" shaped plug on a heavy duty cable with twin fuse holders.
Will also fit: Albrecht AE485, Magnum 257, Magnum Deltaforce etc.
A short power lead suitable for many PMR radios, including Icom, Kenwood & Maxon.
This is also the same connection as used on some CB & Amateur radios, including Magnum & Alinco.
The lead is not fused and just comes with a short length of cable to join into your existing wiring.
A heavy duty power lead which fits many of the Yaesu, Kenwood, Alinco, and Icom VHF/UHF radios.
Supplied with twin fuse holders with 15A fuses fitted
Note: "male" pins in power lead
A heavy duty replacement power lead for the Original President Lincoln and Uniden 2830 radios.
10A cable with 8A fuse fitted.
Original replacement power lead for Superstar 3900EFT & SS-158EDX
6 pin power plug with heavy duty twin fused lead.
Note: this only fits the EFT model, other 3900's use a standard 3 pin.
A replacement 12V power cable which fits many of the Kenwood and Icom HF radios. 6 pin plug.
Supplied with heavy duty cable, twin fuse holders and 20A fuses.
A replacement 12V power lead for HF radios which use a 4 pin plug (eg IC-7000).
An extension 3 pin power lead with fitted fuse holder.
This has a male plug on one end and a female socket on the other.
You can cut this in half to make up a quick disconnect lead for radios that have a fixed power lead?
A replacement power leads for radios where the lead is wired directly into the radio.
Approx 1.5m long with a fitted fuseholder and 3A fuse.
A non reversible quick disconnect to fit in a power lead, supplied on short wire stubs.
Ideal where you need to remove equipment or for connecting it in 2 different locations.
Original replacement power lead to fit various Albrecht radios, including the AE7500 and AE5890.
Fitted with a single fuseholder.
Original power lead for Albrecht AE6891.
Note, this lead does not have an inline fuse holder (the fuse is on the other part attached to the radio).
Heavy duty 16 gauge bullet quick
disconnect lead consisting of non reversible moulded plug and socket
terminating to simple cut end.
Suitable for Motorola GM series PMR transceivers.
Lead is 31.5cm overall in length.
A "universal" HF power lead supplies with 2 different plugs to suit many HF radios.
One of the 6 pin plugs will fit many popular HF radios such as Kenwood, Yaesu, Icom etc.
The other end fits the Ranger rci2970 radios.